How to select matte black ink on epson 3880 printer

#How to select matte black ink on epson 3880 printer update#
#How to select matte black ink on epson 3880 printer manual#
#How to select matte black ink on epson 3880 printer skin#
#How to select matte black ink on epson 3880 printer pro#

It's behind the scenes where the real changes are occurring though. Other than the UltraChrome K3 label (Figure 1) adding the Vivid Magenta, the printers look visually identical.В In fact, even opening up the ink compartments you'll see only a Vivid label on the magenta cartridges to tell you this is a different printer. Both the 3880 and the 3800 it replaces use the same case and controls.

#How to select matte black ink on epson 3880 printer pro#

With the new Stylus Pro 3880 though, Epson has taken one step forward rather than skipping directly to UltraChrome HDR.В Since the 4880, 7880, and 9880 are still current models, this isn't as odd as it might seem.

#How to select matte black ink on epson 3880 printer skin#

The other change is more recent, and so far seen in only two printers вЂ“ the 79 вЂ“ with UltraChrome HDR, adding green and orange to the mix to give skin tones a more accurate appearance as well as fit the needs of graphic designers in addition to photographers.Д«ecause the HDR inkset has been out for a while now, you would probably expect a new printer from Epson to adopt this version. The first is the second generation of UltraChrome K3, which replaced the original magenta and light magenta inks with a new Vivid versions to increase the color range, particularly in the deep blues. Since the 3800 was released, Epson has made two major changes in their pigment ink photo printers. With a good combination of price and size, this C sized printer has filled the needs of photographers looking for the ability to print 17x22 on a variety of media without the bulk or expense of a large format printer. For the past three years, the Epson Stylus Pro 3800 has held this status.

#How to select matte black ink on epson 3880 printer update#

The Printer button next to it on the lower right reopens the Print Settings panel, but gives you a Print option instead of a Save option.When you have the most popular C Size (17') printer on the market, it might not seem that there's a good reason to update it. You can now choose the Print button, lower right, and print the photo. You can also adjust Platen Gap there is you are getting Type 1 Head Strikes.ДЎ4. If you are using non-Epson paper, then you will want to set the Paper Thickness under the Paper Configuration section.

The Save button on the panel seems to only save for the current session.ДЎ3. If you want to create a preset for future sessions do so in the top preset pull-down. It save a little time, but if you get banding turn it off. By the way, dpi is the ink laydown rate, while ppi is the image dependent resolution. Print Quality: The smart money says 1440 dpi for matte, and 2880 dpi for glossy.

If you changed color management you may need to exit Lightroom and restart it to register the change.ДЎ0. The Color selection should be greyed-out and Advanced Color Settings should be off if you choose a profile in step 3. Check the 16-bit box for the Epson 3800.Д©. It should be appropriate for the paper, and requires that you did steps 2, 5,and 6 right.ДЁ.

#How to select matte black ink on epson 3880 printer manual#

That means that your Page Setup is wrong or that the wrong feed has been chosen (e.g., Velvet Fine Art Paper does not come in 4ењ† and requires the Manual Feed). Choose relative and forget about this if you follow step 4. The enigmatic rendering intent for dealing with out-of-gamut colors (perceptual or relative) follows. Epson uses acronyms in its profile names (why I donвЂ™t know) so a cheat list is shown below. Click the pull down arrows and either choose a profile for your paper or вЂњmanaged by printer.вЂќ (A blog entry on where to get these profiles and populate this list is here). What you choose here makes a big difference so choose wisely. You have to choose a paper profile, OR let the printer manage color. Now it is a bit tricky, so pay attention. Smart money says set the sharpening to Standard, and use Media Type Glossy when printing on glossy, luster, semi-gloss, an F-type or Baryta paper. The 3800 can accept 16 bit data check it here and in the print settings (step 8, below). Learn which ink your paper uses (Photo Black for glossy, Matte Black for matte) and batch the papers. This is also where you make the first choice as to media (second and third is coming up), which affects ink type to be used. Lots of reasons to do this (mainly because this is the native resolution of the printer). Set the print resolution to 360 ppi and forget it.